P0335 on a 2022 Ford Escape
Crankshaft Position Sensor Circuit Fault
P0335 on a 2022 Ford Escape indicates crankshaft position sensor circuit fault. Stop driving and diagnose it before continuing — it can signal an unsafe condition. The most common cause is failed crankshaft position sensor (heat-related failure) (typically $100–$400). Confirm the root cause before replacing parts.
What does P0335 mean on a 2022 Ford Escape?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
This guide covers P0335 across the 2020-2024 Ford Escape generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Ford Escape with P0335?
No. P0335 is a critical-severity code on the 2022 Ford Escape — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.
What are the symptoms of P0335 on a 2022 Ford Escape?
- Check Engine Light is illuminated
- Engine cranks but will not start
- Intermittent stalling that worsens with engine heat
- Hard starting after a long drive (heat-soak failure)
- Sudden stalling at highway speed with restart difficulty
- Tachometer reads zero or fluctuates while running
- Hard cold start with extended crank time
What causes P0335 on a 2022 Ford Escape?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed crankshaft position sensor (heat-related failure) Heat-soak failure pattern is the textbook P0335 — fails when hot, recovers when cold. | Most common | $100–$400 |
| Damaged or melted sensor wiring near the exhaust | Common | $80–$350 |
| Corroded crank sensor connector | Common | $30–$200 |
| Damaged crank reluctor / tone ring (rare, requires teardown) | Rare | $1,500–$4,000 |
| Loose or improperly torqued sensor (cannot read gap correctly) | Occasional | $20–$100 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2022 Ford Escape
-
Confirm the engine cranks but doesn't fire
P0335 typically presents as a crank-no-start. Confirm by cranking — the engine should rotate normally but never fire. If the engine fires intermittently, the sensor may be marginal; if it never fires, the sensor or wiring is fully out.
Tools: Common observation
-
Locate the sensor on the engine
Crank sensors are typically mounted on the timing cover (front of engine), the bell housing (rear of engine), or on the side of the block. Consult the service manual. Most are accessible from underneath with a basic socket set.
Tools: Vehicle-specific service information
-
Inspect wiring and connector
The sensor wiring routes close to the exhaust on many engines. Look for heat-damaged insulation, broken wires, or melted connectors. Sensor connectors near the firewall accumulate water and corrode — clean thoroughly.
Tools: Flashlight, Electrical contact cleaner
-
Test sensor resistance and reference voltage
Most crank sensors are inductive (variable reluctance) with approximately 200–2,000 Ω resistance, or Hall-effect with a 5 V reference. Compare to the service manual. With the connector unplugged and key on, verify the 5 V reference reaches the connector (Hall-effect sensors).
Tools: Multimeter, Wiring diagram
-
Heat-soak test for intermittent failures
P0335 that comes and goes with temperature is the textbook heat-soak failure pattern. Drive until the engine is hot, then attempt a restart immediately. If the engine cranks-no- starts hot and starts fine after cooling, the sensor is the cause even if cold-bench tests pass.
Tools: Patience
NHTSA complaints & recalls for the 2022 Ford Escape
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Ford Escape. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Escape diagnostics.
- FUEL SYSTEM 57
- GASOLINE 57
- POWER TRAIN 24
- ENGINE 24
- SERVICE BRAKES 33
19 active recalls
- SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER Nov 2021
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco Sport and Escape vehicles. The rear brake linings may have been manufactured incorrectly, which can affect braking performance. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle…
NHTSA campaign 21V922000 - ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY Mar 2022
Ford Motor Company (Ford) is recalling certain 2022 Corsair and 2021-2022 Escape vehicles equipped with a 2.5L Hybrid powertrain. The high voltage battery may fail, resulting in a sudden loss of drive power.…
NHTSA campaign 22V149000 - ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION Mar 2022
Ford Motor Company (Ford) is recalling certain 2020-2022 Escape and 2021-2022 Bronco Sport vehicles equipped with 1.5L engines. The engine oil separator housing may crack and develop an oil leak.…
NHTSA campaign 22V191000 - ENGINE AND ENGINE COOLING Jul 2022
Ford Motor Company (Ford) is recalling certain 2020-2022 Escape, 2021-2022 Lincoln Corsair, and 2022 Maverick vehicles equipped with 2.5L HEV or PHEV engines. In the event of an engine failure, engine oil and fuel vapor may be released into the engine compartment and accumulate…
NHTSA campaign 22V484000
How do I fix P0335 on a 2022 Ford Escape?
- Replace the crankshaft position sensor with an OEM part
- Repair damaged sensor wiring or connector
- Re-torque sensor to specification
- Replace damaged reluctor wheel (rare, major job)
About the 2020-2024 Ford Escape
The 2020-2024 Ford Escape was commonly sold with the following powertrains: 1.5L EcoBoost I3, 2.0L EcoBoost I4, 2.5L Hybrid I4. Common trims include S, SE, SEL, Titanium.
The “crank-no-start” pattern that distinguishes P0335 from no fuel / no spark
Three different no-start patterns:
- No spark, no fuel pulse — crank sensor (P0335). The engine cranks normally but the ECM never commands injectors or coils because it has no timing reference.
- Fuel but no spark — ignition system. Coils or coil drivers.
- Spark but no fuel — fuel system. Pump, relay, or wiring.
A scan tool can confirm P0335 by reading the crank RPM PID during cranking — it should report the cranking RPM (typically 150–300 RPM). If it reports zero or doesn’t update, the crank signal is the problem.
Heat-soak failure: the most frustrating intermittent
A failing crank sensor often works perfectly cold and fails after the engine reaches operating temperature. The pattern owners describe: drive for 30+ minutes, stop somewhere (gas station, errand), and the car will not restart for 15-30 minutes — then starts fine. This is the crank sensor failing under heat. A new sensor is the only fix.
Replace the sensor preemptively if you see this pattern; the failure mode worsens until the vehicle will not start at all.
Why P0335 is more serious than P0340 (cam sensor)
The cam sensor is supplementary on most engines — the ECM can run on the crank signal alone in a “limp” mode. The crank sensor is not supplementary; without it the ECM has no idea where any piston is, when to fire, or even whether the engine is running. P0335 = engine off until fixed. P0340 = engine runs poorly but runs.
P0335 on a 2022 Ford Escape: frequently asked questions
What does diagnostic trouble code P0335 mean on a 2022 Ford Escape?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
What are the symptoms of P0335 on a 2022 Ford Escape?
Check Engine Light is illuminated. Engine cranks but will not start. Intermittent stalling that worsens with engine heat. Hard starting after a long drive (heat-soak failure). Sudden stalling at highway speed with restart difficulty. Tachometer reads zero or fluctuates while running. Hard cold start with extended crank time
What causes P0335 on a 2022 Ford Escape?
Failed crankshaft position sensor (heat-related failure) (most-common). Damaged or melted sensor wiring near the exhaust (common). Corroded crank sensor connector (common). Damaged crank reluctor / tone ring (rare, requires teardown) (rare). Loose or improperly torqued sensor (cannot read gap correctly) (occasional). Failed PCM input (rare) (rare)
Is it safe to drive a 2022 Ford Escape with P0335?
No. P0335 is a critical-severity code on the 2022 Ford Escape — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.