P0335 on a 2012 Nissan Altima
Crankshaft Position Sensor Circuit Fault
P0335 on a 2012 Nissan Altima indicates crankshaft position sensor circuit fault. Stop driving and diagnose it before continuing — it can signal an unsafe condition. The most common cause is failed crankshaft position sensor (heat-related failure) (typically $100–$400). Confirm the root cause before replacing parts.
What does P0335 mean on a 2012 Nissan Altima?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
This guide covers P0335 across the 2010-2014 Nissan Altima generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Nissan Altima with P0335?
No. P0335 is a critical-severity code on the 2012 Nissan Altima — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.
What are the symptoms of P0335 on a 2012 Nissan Altima?
- Check Engine Light is illuminated
- Engine cranks but will not start
- Intermittent stalling that worsens with engine heat
- Hard starting after a long drive (heat-soak failure)
- Sudden stalling at highway speed with restart difficulty
- Tachometer reads zero or fluctuates while running
- Hard cold start with extended crank time
What causes P0335 on a 2012 Nissan Altima?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed crankshaft position sensor (heat-related failure) Heat-soak failure pattern is the textbook P0335 — fails when hot, recovers when cold. | Most common | $100–$400 |
| Damaged or melted sensor wiring near the exhaust | Common | $80–$350 |
| Corroded crank sensor connector | Common | $30–$200 |
| Damaged crank reluctor / tone ring (rare, requires teardown) | Rare | $1,500–$4,000 |
| Loose or improperly torqued sensor (cannot read gap correctly) | Occasional | $20–$100 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2012 Nissan Altima
-
Confirm the engine cranks but doesn't fire
P0335 typically presents as a crank-no-start. Confirm by cranking — the engine should rotate normally but never fire. If the engine fires intermittently, the sensor may be marginal; if it never fires, the sensor or wiring is fully out.
Tools: Common observation
-
Locate the sensor on the engine
Crank sensors are typically mounted on the timing cover (front of engine), the bell housing (rear of engine), or on the side of the block. Consult the service manual. Most are accessible from underneath with a basic socket set.
Tools: Vehicle-specific service information
-
Inspect wiring and connector
The sensor wiring routes close to the exhaust on many engines. Look for heat-damaged insulation, broken wires, or melted connectors. Sensor connectors near the firewall accumulate water and corrode — clean thoroughly.
Tools: Flashlight, Electrical contact cleaner
-
Test sensor resistance and reference voltage
Most crank sensors are inductive (variable reluctance) with approximately 200–2,000 Ω resistance, or Hall-effect with a 5 V reference. Compare to the service manual. With the connector unplugged and key on, verify the 5 V reference reaches the connector (Hall-effect sensors).
Tools: Multimeter, Wiring diagram
-
Heat-soak test for intermittent failures
P0335 that comes and goes with temperature is the textbook heat-soak failure pattern. Drive until the engine is hot, then attempt a restart immediately. If the engine cranks-no- starts hot and starts fine after cooling, the sensor is the cause even if cold-bench tests pass.
Tools: Patience
NHTSA complaints & recalls for the 2012 Nissan Altima
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Nissan Altima. Use these to gauge how common a problem is on your specific vehicle before you start chasing Nissan Altima diagnostics.
- POWER TRAIN 149
- ENGINE 68
- VEHICLE SPEED CONTROL 49
- UNKNOWN OR OTHER 56
- AIR BAGS 56
4 active recalls
- AIR BAGS:SIDE/WINDOW Feb 2012
NISSAN IS RECALLING CERTAIN MODEL YEAR 2012 ALTIMA AND VERSA VEHICLES. THESE VEHICLES MAY BE EQUIPPED WITH SIDE CURTAIN AIR BAGS THAT CONTAIN AN INCORRECT PROPELLANT MIXTURE FOR THE INITIATOR COMPONENT USED, RESULTING IN INSUFFICIENT OUTPUT OF COMPRESSED GAS.…
NHTSA campaign 12V055000 - AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE Aug 2011
NISSAN IS RECALLING CERTAIN MODEL YEAR 2012 NISSAN ALTIMA VEHICLES MANUFACTURED FROM JUNE 15, 2011, THROUGH JUNE 21, 2011 AND MODEL YEAR 2012 NISSAN NV VEHICLES MANUFACTURED FROM JUNE 23, 2011, THROUGH JUNE 28, 2011 BECAUSE THE AIR BAG CONTROL UNIT (ACU) WAS ASSEMBLED INCORRECTLY…
NHTSA campaign 11V408000 - STEERING Oct 2012
Nissan is recalling certain model year 2012-2013 Altima vehicles manufactured from May 10, 2012, through July 26, 2012. These vehicles may have been equipped with transverse link bolts and power steering rack bolts that were not torqued to proper specification.…
NHTSA campaign 12V494000 - SUSPENSION Jul 2011
NISSAN IS RECALLING CERTAIN MODEL YEAR 2011-2012 NISSAN ALTIMA SEDAN VEHICLES MANUFACTURED FROM APRIL 25, 2011, THROUGH JUNE 10, 2011 AT THE CANTON, MISSISSIPPI PLANT. THE TRANSVERSE LINK BOLT MAY NOT HAVE BEEN TORQUED TO THE PROPER SPECIFICATION. THIS CONDITION COULD CAUSE THE…
NHTSA campaign 11V371000
How do I fix P0335 on a 2012 Nissan Altima?
- Replace the crankshaft position sensor with an OEM part
- Repair damaged sensor wiring or connector
- Re-torque sensor to specification
- Replace damaged reluctor wheel (rare, major job)
About the 2010-2014 Nissan Altima
The 2010-2014 Nissan Altima was commonly sold with the following powertrains: 2.5L I4, 2.0L VC-Turbo I4, 3.5L V6. Common trims include S, SV, SR, SL, Platinum.
The “crank-no-start” pattern that distinguishes P0335 from no fuel / no spark
Three different no-start patterns:
- No spark, no fuel pulse — crank sensor (P0335). The engine cranks normally but the ECM never commands injectors or coils because it has no timing reference.
- Fuel but no spark — ignition system. Coils or coil drivers.
- Spark but no fuel — fuel system. Pump, relay, or wiring.
A scan tool can confirm P0335 by reading the crank RPM PID during cranking — it should report the cranking RPM (typically 150–300 RPM). If it reports zero or doesn’t update, the crank signal is the problem.
Heat-soak failure: the most frustrating intermittent
A failing crank sensor often works perfectly cold and fails after the engine reaches operating temperature. The pattern owners describe: drive for 30+ minutes, stop somewhere (gas station, errand), and the car will not restart for 15-30 minutes — then starts fine. This is the crank sensor failing under heat. A new sensor is the only fix.
Replace the sensor preemptively if you see this pattern; the failure mode worsens until the vehicle will not start at all.
Why P0335 is more serious than P0340 (cam sensor)
The cam sensor is supplementary on most engines — the ECM can run on the crank signal alone in a “limp” mode. The crank sensor is not supplementary; without it the ECM has no idea where any piston is, when to fire, or even whether the engine is running. P0335 = engine off until fixed. P0340 = engine runs poorly but runs.
P0335 on a 2012 Nissan Altima: frequently asked questions
What does diagnostic trouble code P0335 mean on a 2012 Nissan Altima?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
What are the symptoms of P0335 on a 2012 Nissan Altima?
Check Engine Light is illuminated. Engine cranks but will not start. Intermittent stalling that worsens with engine heat. Hard starting after a long drive (heat-soak failure). Sudden stalling at highway speed with restart difficulty. Tachometer reads zero or fluctuates while running. Hard cold start with extended crank time
What causes P0335 on a 2012 Nissan Altima?
Failed crankshaft position sensor (heat-related failure) (most-common). Damaged or melted sensor wiring near the exhaust (common). Corroded crank sensor connector (common). Damaged crank reluctor / tone ring (rare, requires teardown) (rare). Loose or improperly torqued sensor (cannot read gap correctly) (occasional). Failed PCM input (rare) (rare)
Is it safe to drive a 2012 Nissan Altima with P0335?
No. P0335 is a critical-severity code on the 2012 Nissan Altima — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.