P0156 on GMC vehicles
Post-Cat O2 Sensor Circuit Fault (Bank 2) — what it means on a GMC, whether it's safe to drive, and the fixes by model and year.
P0156 on a GMC means post-cat o2 sensor circuit fault (bank 2). Most vehicles stay drivable short-term, but diagnose it promptly. The most common cause is failed bank 2 downstream o2 sensor (typically $150–$450). Pick your GMC model below for its known failure patterns, recalls, and TSBs.
What does P0156 mean on a GMC?
P0156 is the Bank 2 counterpart of P0136. The ECM has detected a general circuit fault on the Bank 2 downstream oxygen sensor — the one after the catalytic converter on the cylinder bank that does NOT contain cylinder number 1. It is the catch-all code: it covers wiring faults, intermittent connections, and readings that fall outside expectations in a way that does not fit the narrower codes P0157 (low voltage), P0158 (high voltage), or P0160 (no activity). Because Bank 2 only exists on engines with two cylinder banks, P0156 applies to V6, V8, V10, V12, and flat / boxer engines only.
P0156 is a standardized OBD-II code, so its definition is the same on every GMC. What differs by model and engine is which cause is most likely — pick your GMC model below for a diagnosis tuned to its known failure patterns, recalls, and TSBs.
Is it safe to drive a GMC with P0156?
In most cases a GMC stays drivable for short trips with P0156 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test. Exact tolerance depends on the model and engine.
What causes P0156 on a GMC?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed Bank 2 downstream O2 sensor | Most common | $150–$450 |
| Damaged sensor wiring chafed or melted against the exhaust | Common | $80–$350 |
| Corroded Bank 2 downstream O2 sensor connector | Common | $30–$200 |
| Exhaust leak upstream of the Bank 2 downstream sensor | Occasional | $100–$500 |
| Damaged or crushed sensor pigtail from a previous repair | Occasional | $80–$300 |
| Failed PCM input for the Bank 2 downstream circuit | Rare | $400–$1,500 |
Repair costs are typical US ranges and vary by GMC model, model year, and labor rate. A diagnostic trouble code is a symptom, not a guaranteed failed part — confirm the root cause before replacing anything.
P0156 by GMC model
Select your GMC model and year for a P0156 diagnosis tuned to that vehicle's failure patterns, recalls, and TSBs.
GMC Sierra 1500
988 NHTSA owner complaints · 14 recalls on record across the years covered below.
Complaint and recall counts are NHTSA totals for the model years covered on this site, not counts specific to P0156.
P0156 on other makes
Other codes on GMC vehicles
P0156 on a GMC: frequently asked questions
What does diagnostic trouble code P0156 mean on a GMC?
P0156 is the Bank 2 counterpart of P0136. The ECM has detected a general circuit fault on the Bank 2 downstream oxygen sensor — the one after the catalytic converter on the cylinder bank that does NOT contain cylinder number 1. It is the catch-all code: it covers wiring faults, intermittent connections, and readings that fall outside expectations in a way that does not fit the narrower codes P0157 (low voltage), P0158 (high voltage), or P0160 (no activity). Because Bank 2 only exists on engines with two cylinder banks, P0156 applies to V6, V8, V10, V12, and flat / boxer engines only. P0156 is a standardized OBD-II code, so the definition is the same on every GMC — which cause is most likely varies by model and engine.
What are the symptoms of P0156 on a GMC?
Check Engine Light is illuminated. Catalyst readiness monitor will not complete. Often no drivability symptoms at all. Possible slight reduction in fuel economy. Vehicle will fail emissions / smog testing
What causes P0156 on a GMC?
Failed Bank 2 downstream O2 sensor (most-common). Damaged sensor wiring chafed or melted against the exhaust (common). Corroded Bank 2 downstream O2 sensor connector (common). Exhaust leak upstream of the Bank 2 downstream sensor (occasional). Damaged or crushed sensor pigtail from a previous repair (occasional). Failed PCM input for the Bank 2 downstream circuit (rare)
Is it safe to drive a GMC with P0156?
In most cases a GMC stays drivable for short trips with P0156 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test. Exact tolerance depends on the model and engine.