P0141 on a 2022 Honda Odyssey
Post-Cat O2 Heater Circuit (Bank 1 Downstream)
P0141 on a 2022 Honda Odyssey indicates post-cat o2 heater circuit (bank 1 downstream). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed bank 1 downstream o2 sensor heater element (typically $150–$450). Confirm the root cause before replacing parts.
What does P0141 mean on a 2022 Honda Odyssey?
P0141 is set when the heater element built into the Bank 1 downstream (post-catalyst) oxygen sensor does not draw the expected current when commanded on. The downstream sensor's job is to monitor catalyst efficiency, and it needs its heater to reach operating temperature before it can produce a useful signal. P0141 is the downstream counterpart of P0135.
This guide covers P0141 across the 2020-2024 Honda Odyssey generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Honda Odyssey with P0141?
In most cases a 2022 Honda Odyssey stays drivable for short trips with P0141 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0141 on a 2022 Honda Odyssey?
- Check Engine Light is illuminated
- Catalyst readiness monitor will not complete (vehicle fails emissions readiness)
- Slight reduction in fuel economy
- Often no drivability symptoms at all
- Vehicle will fail OBD-II emissions / smog testing
What causes P0141 on a 2022 Honda Odyssey?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed Bank 1 downstream O2 sensor heater element | Most common | $150–$450 |
| Blown O2 heater fuse | Common | $5–$30 |
| Damaged sensor wiring (chafed against exhaust) | Common | $80–$350 |
| Corroded O2 sensor connector | Common | $30–$200 |
| Failed O2 heater relay (vehicles with one) | Occasional | $30–$150 |
| PCM driver failure (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2022 Honda Odyssey
-
Identify the Bank 1 downstream sensor location
The downstream O2 sensor is after the catalytic converter on Bank 1. On most modern vehicles this is under the vehicle, on the exhaust pipe a few inches behind the catalyst's outlet flange. Track the sensor wiring back to the chassis harness.
Tools: Vehicle-specific service information, Vehicle lift or jack stands
-
Check the O2 heater fuse
Many vehicles share a single fuse for all O2 heaters; some have separate fuses per bank. Verify the correct fuse with a test light and replace if blown. If the fuse blows again immediately, a short to ground in the harness or sensor is the cause.
Tools: Test light or multimeter, Replacement fuse
-
Measure heater resistance at the sensor
Unplug the downstream sensor. Measure resistance across the heater terminals — typically 3 to 15 Ω cold. Infinite means open (failed element). Near zero means shorted heater.
Tools: Multimeter, Wiring diagram
-
Test heater current during operation
Clamp a low-current ammeter around the heater wire while the engine runs. A working heater draws approximately 0.8 to 2 A. Zero current with voltage present at the connector confirms an open heater. Higher than 2 A means a partially shorted heater will likely blow the fuse soon.
Tools: Multimeter with current function, Low-current clamp (preferred)
-
Inspect for harness chafing near the exhaust
The downstream sensor harness runs along the exhaust under the vehicle. Exhaust heat over time can melt insulation and short the heater wires. Visually inspect the harness; any darkened or melted-looking section requires repair.
Tools: Flashlight, Wire repair supplies
NHTSA complaints & recalls for the 2022 Honda Odyssey
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Honda Odyssey. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda Odyssey diagnostics.
- ENGINE 15
- POWER TRAIN 14
- ELECTRICAL SYSTEM 33
- FORWARD COLLISION AVOIDANCE 27
- UNKNOWN OR OTHER 17
9 active recalls
- TIRES:SIDEWALL Sep 2021
Honda (American Honda Motor Co.) is recalling certain 2022 Odyssey vehicles equipped with Bridgestone tires. The affected vehicles may have a tire that contains a pinhole, causing a slow air leak. As such, these tires fail to comply with the requirements of Federal Motor Vehicl…
NHTSA campaign 21V768000 - SEATS Jun 2021
Honda (American Honda Motor Co.) is recalling certain 2022 Odyssey vehicles. The second-row outboard seats may have deformed seat rail locking mechanisms, which could prevent the seat rails from locking into place.…
NHTSA campaign 21V432000 - VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR Mar 2023
Honda (American Honda Motor Co) is recalling certain 2020-2021 Pilot and Ridgeline, and 2020-2022 Passport and Odyssey vehicles. The heating pads behind both side-view mirrors may not be bonded properly, allowing the mirror glass to detach. As such, these vehicles fail to compl…
NHTSA campaign 23V174000 - BACK OVER PREVENTION:DISPLAY FUNCTION Jun 2023
Honda (American Honda Motor Co.) is recalling certain 2018-2023 Odyssey, 2019-2022 Pilot, and 2019-2023 Passport vehicles. Due to a faulty Media Oriented Systems Transport (MOST) communication coaxial cable connector, the rearview camera image may not appear on the display. As…
NHTSA campaign 23V431000
How do I fix P0141 on a 2022 Honda Odyssey?
- Replace the Bank 1 downstream O2 sensor with an OEM part
- Replace the O2 heater fuse
- Repair damaged downstream O2 sensor wiring
- Replace the O2 heater relay
About the 2020-2024 Honda Odyssey
The 2020-2024 Honda Odyssey was commonly sold with the following powertrains: 3.5L V6. Common trims include LX, EX, EX-L, Touring, Elite.
Why P0141 specifically affects emissions testing
The catalyst readiness monitor cannot complete unless the downstream sensor reaches operating temperature within its time window. P0141 prevents the heater from working, so the monitor never completes. Even if you clear the code, the readiness flag will show “not ready” — and most emissions testing programs treat “not ready” as a failure.
This is why P0141 is one of the most common codes that causes emissions test failures even after the underlying issue is “resolved.” The fix has to physically repair the heater, then run the drive cycle to complete the monitor.
Drive cycle to complete the catalyst monitor
After fixing P0141:
- Cold soak (engine off 8+ hours)
- Cold start, idle 2.5 minutes with A/C and rear defrost on
- Accelerate gently to 55 mph and cruise 5 minutes
- Decelerate to 20 mph without braking, then accelerate back to 55 mph
- Hold 55 mph cruise for 5 minutes
- Decelerate to a stop and idle 2 minutes
Confirm the catalyst monitor reads “complete” before scheduling an emissions test. Some scan tools show this directly; many auto parts stores will scan readiness monitors for free.
P0141 vs P0135
- P0135 — Bank 1 upstream (sensor 1) heater failure
- P0141 — Bank 1 downstream (sensor 2) heater failure
Both setting together suggests a common cause — shared fuse, shared ground, or a wiring issue rather than two sensors failing simultaneously.