P0138 on a 2017 Ford Escape
Post-Cat O2 Sensor High Voltage (Bank 1 Downstream)
P0138 on a 2017 Ford Escape indicates post-cat o2 sensor high voltage (bank 1 downstream). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed bank 1 downstream o2 sensor (stuck high) (typically $150–$450). Confirm the root cause before replacing parts.
What does P0138 mean on a 2017 Ford Escape?
P0138 is set when the downstream (post-catalyst) oxygen sensor on Bank 1 reports a voltage above the calibrated maximum (typically above 1.0 V) for an extended period. The downstream sensor normally sits at a relatively steady 0.6–0.8 V because the catalyst smooths the rich/lean oscillation it sees coming in. A reading stuck above 1.0 V is either a genuine very-rich condition reaching the catalyst, a shorted signal wire, or a failed sensor biased high.
This guide covers P0138 across the 2015-2019 Ford Escape generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Ford Escape with P0138?
In most cases a 2017 Ford Escape stays drivable for short trips with P0138 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0138 on a 2017 Ford Escape?
- Check Engine Light is illuminated
- Possible mild reduction in fuel economy
- Often no drivability symptoms at all
- Vehicle may fail emissions / smog testing
- Sometimes accompanied by P0172 (rich Bank 1)
What causes P0138 on a 2017 Ford Escape?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed Bank 1 downstream O2 sensor (stuck high) | Most common | $150–$450 |
| Shorted-to-power O2 signal wire (sensor reads max) | Common | $80–$350 |
| Genuine rich condition reaching the catalyst (leaking injector, FPR) Address the rich condition; the sensor is correctly reporting it. | Common | $150–$1,200 |
| Damaged sensor connector — corrosion biasing the signal | Common | $30–$200 |
| Internal sensor short due to contamination | Occasional | $150–$450 |
| Coolant or oil in the exhaust (head gasket / valve seals) | Rare | $1,200–$3,500 |
How to diagnose this on a 2017 Ford Escape
-
Determine whether the reading is real or sensor-reported
Read fuel trims at idle and 2500 RPM. If Bank 1 LTFT is around −10 % or worse (the ECM pulling fuel out), the engine is genuinely running rich and the downstream sensor is correctly reporting it. If LTFT is near zero, the engine is fine and the sensor or its wiring is the problem.
Tools: Scan tool with fuel trim PIDs
-
Inspect for shorted signal wire
Disconnect the Bank 1 downstream O2 sensor. With the connector unplugged and the key on, scan-tool voltage on the signal wire should fall to bias voltage (0.4–0.5 V). If voltage stays high (above 1 V), the signal wire is shorted to power somewhere between the sensor and the PCM.
Tools: Scan tool, Multimeter
-
Verify with a known-good sensor
The downstream sensor is essentially a slow O2 sensor that should not switch rapidly. If a known-good sensor (or the Bank 2 downstream sensor if equipped) reads correctly while the Bank 1 downstream sticks high, the Bank 1 sensor is bad.
Tools: Scan tool with sensor swap capability
-
Inspect for fuel contamination of the catalyst
If a separate rich-running fault (P0172, stuck injector) has been present for months, fuel may have entered the catalyst and altered its oxygen-storage behavior — which the downstream sensor sees as a chronic rich signal. This requires the rich cause fixed AND likely catalyst replacement.
Tools: Diagnostic history review
-
Check for exhaust system damage
Look for any damage to the exhaust between the catalyst and the downstream sensor that could let oil mist or coolant into the exhaust stream. Coolant entering the exhaust (head gasket, cracked head) creates rich-mimicking sensor readings.
Tools: Visual inspection, Coolant pressure tester
Known Technical Service Bulletins for the 2015-2019 Ford Escape
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Ford Escape.
- UNKNOWN OR OTHER Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - STRUCTURE Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Nov 26, 2025
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
NHTSA #11025837 - POWER TRAIN Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611 - ELECTRICAL SYSTEM Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
NHTSA complaints & recalls for the 2017 Ford Escape
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Ford Escape. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Escape diagnostics.
- ENGINE 1476
- ENGINE AND ENGINE COOLING 498
- POWER TRAIN 374
- ELECTRICAL SYSTEM 149
- UNKNOWN OR OTHER 146
3 active recalls
- VISIBILITY:POWER WINDOW DEVICES AND CONTROLS Aug 2016
Ford Motor Company (Ford) is recalling certain model year 2017 Ford Escape Titanium and SE vehicles manufactured October 5, 2015, to May 12, 2016. The settings for the closing-force of the power-operated windows may allow the windows to close on an object such as a body part and…
NHTSA campaign 16V617000 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL) Jun 2022
Ford Motor Company (Ford) is recalling certain 2013-2019 Escape, 2013-2018 C-Max, 2013-2016 Fusion, 2013-2021 Transit Connect, and 2015-2018 Edge vehicles. The bushing that attaches the shifter cable to the transmission may degrade or detach.…
NHTSA campaign 22V413000 - EQUIPMENT:ELECTRICAL:ENGINE BLOCK HEATER Jan 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.…
NHTSA campaign 26V011000
How do I fix P0138 on a 2017 Ford Escape?
- Replace the Bank 1 downstream O2 sensor with an OEM part
- Repair shorted-to-power O2 signal wire
- Address underlying rich condition (P0172) first if present
- Clean or replace corroded O2 sensor connector
- Repair coolant or oil entry into the exhaust (root cause)
About the 2015-2019 Ford Escape
The 2015-2019 Ford Escape was commonly sold with the following powertrains: 1.5L EcoBoost I3, 2.0L EcoBoost I4, 2.5L Hybrid I4. Common trims include S, SE, SEL, Titanium.
What the downstream O2 sensor actually does
Unlike the upstream sensor, which feeds closed-loop fuel control, the downstream sensor’s main job is to monitor catalyst efficiency. It also provides a slow secondary fuel-trim correction. A properly functioning catalyst smooths the rich/lean oscillation coming from the engine — so the downstream voltage normally hovers steadily around 0.6–0.8 V instead of switching.
P0138 means that smoothing is gone and the post-cat reading is biased high — either the cat is gone, the engine is running rich, or the sensor itself is misreading.
P0138 with no other rich codes
This pattern usually points at the sensor or its wiring rather than a fuel system problem. A genuine rich condition severe enough to peg the downstream sensor at >1 V would also set P0172. P0138 alone with normal fuel trims is the textbook “downstream sensor has failed” pattern.
When P0138 reflects a real fuel problem
If P0138 sets alongside P0172 (system too rich), P0171 (lean) with heavy intake leak, or recent fuel-injector work, the sensor is likely correct and the fueling is at fault. Replacing the sensor without fixing the upstream condition will result in P0138 returning within days.
P0138 on a 2017 Ford Escape: frequently asked questions
What does diagnostic trouble code P0138 mean on a 2017 Ford Escape?
P0138 is set when the downstream (post-catalyst) oxygen sensor on Bank 1 reports a voltage above the calibrated maximum (typically above 1.0 V) for an extended period. The downstream sensor normally sits at a relatively steady 0.6–0.8 V because the catalyst smooths the rich/lean oscillation it sees coming in. A reading stuck above 1.0 V is either a genuine very-rich condition reaching the catalyst, a shorted signal wire, or a failed sensor biased high.
What are the symptoms of P0138 on a 2017 Ford Escape?
Check Engine Light is illuminated. Possible mild reduction in fuel economy. Often no drivability symptoms at all. Vehicle may fail emissions / smog testing. Sometimes accompanied by P0172 (rich Bank 1)
What causes P0138 on a 2017 Ford Escape?
Failed Bank 1 downstream O2 sensor (stuck high) (most-common). Shorted-to-power O2 signal wire (sensor reads max) (common). Genuine rich condition reaching the catalyst (leaking injector, FPR) (common). Damaged sensor connector — corrosion biasing the signal (common). Internal sensor short due to contamination (occasional). Coolant or oil in the exhaust (head gasket / valve seals) (rare)
Is it safe to drive a 2017 Ford Escape with P0138?
In most cases a 2017 Ford Escape stays drivable for short trips with P0138 active, but it should be diagnosed and repaired promptly — this is a low-severity code. Ignoring it can lead to further damage or a failed emissions test.