P0136 on a 2022 Honda HR-V
Post-Cat O2 Sensor Circuit Fault (Bank 1)
P0136 on a 2022 Honda HR-V indicates post-cat o2 sensor circuit fault (bank 1). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed bank 1 downstream o2 sensor (typically $150–$450). Confirm the root cause before replacing parts.
What does P0136 mean on a 2022 Honda HR-V?
P0136 is set when the ECM detects a general circuit fault on the Bank 1 downstream (post-catalyst) oxygen sensor. Unlike the more specific P0137 (low voltage), P0138 (high voltage), or P0140 (no activity), P0136 is the generic circuit code that covers wiring issues, intermittent connection problems, or signals that go outside expected ranges in a way that doesn't fit a more specific fault category.
This guide covers P0136 across the 2020-2024 Honda HR-V generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Honda HR-V with P0136?
In most cases a 2022 Honda HR-V stays drivable for short trips with P0136 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0136 on a 2022 Honda HR-V?
- Check Engine Light is illuminated
- Catalyst readiness monitor will not complete
- Possible slight reduction in fuel economy
- Often no drivability symptoms
- Vehicle will fail emissions / smog testing
What causes P0136 on a 2022 Honda HR-V?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed Bank 1 downstream O2 sensor | Most common | $150–$450 |
| Damaged sensor wiring (chafed against exhaust) | Common | $80–$350 |
| Corroded O2 sensor connector | Common | $30–$200 |
| Exhaust leak upstream of the downstream sensor | Occasional | $100–$500 |
| Damaged or compressed sensor pigtail from a previous repair | Occasional | $80–$300 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2022 Honda HR-V
-
Read all O2-related codes to refine the picture
P0136 alone is generic. With P0137 it points at low voltage specifically; with P0138 at high voltage; with P0140 at no activity at all; with P0141 at the heater. Cross-referencing tells you whether the diagnostic should target wiring, sensor element, or heater.
Tools: Scan tool with full code retrieval
-
Inspect the sensor wiring
Trace the downstream sensor's harness from the sensor body back to the chassis connector. Look for melted insulation (from exhaust contact), chafing against suspension components, or rodent damage. Repair before replacing the sensor.
Tools: Flashlight, Inspection mirror, Wire repair supplies
-
Test the sensor connector
Disconnect and inspect for water intrusion, corrosion, bent pins. Clean with electrical contact cleaner. The downstream connector sits under the vehicle and gets road spray; corrosion is common after a few salt-belt winters.
Tools: Electrical contact cleaner, Magnifying glass
-
Graph the sensor signal
With engine warm and held at 2500 RPM, watch the Bank 1 downstream O2 voltage. A healthy sensor sits relatively steady around 0.6–0.8 V. Rapid switching, signal stuck at one value, or no signal at all confirms a sensor or wiring issue.
Tools: Scan tool with graphing PIDs
-
Verify the bias voltage from the PCM
Disconnect the sensor and key on. The scan tool should still show bias voltage (typically 0.4–0.5 V) at the connector. If not present, the issue is between the connector and the PCM, not the sensor.
Tools: Scan tool, Multimeter
NHTSA complaints & recalls for the 2022 Honda HR-V
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Honda HR-V. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda HR-V diagnostics.
- ENGINE 16
- POWER TRAIN 14
- VEHICLE SPEED CONTROL 12
- ELECTRICAL SYSTEM 24
- UNKNOWN OR OTHER 14
3 active recalls
- BACK OVER PREVENTION:DISPLAY FUNCTION Feb 2023
Honda (American Honda Motor Co.) is recalling certain 2018-2020 Fit and 2019-2022 HR-V vehicles. The rearview camera image may not display when the engine is started with a key, due to a design error in the audio display power circuit. As such, these vehicles fail to comply wit…
NHTSA campaign 23V046000 - AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION:FRONT PASSENGER Feb 2024
Honda (American Honda Motor Co.) is recalling certain 2020-2022 Pilot, Accord, Civic sedan, HR-V, Odyssey, 2020 Civic coupe, Fit, 2021-2022 Civic hatchback, 2021 Civic Type R, Insight, 2020-2021 CR-V, CR-V Hybrid, Passport, Ridgeline, Accord Hybrid, 2020 Acura MDX, 2022 Acura MDX…
NHTSA campaign 24V064000 - BACK OVER PREVENTION:DISPLAY FUNCTION May 2024
Honda (America Honda Motor Co.) is recalling certain 2018-2020 Fit and 2019-2022 HR-V vehicles that were previously recalled under NHTSA recall number 23V-046. The rearview camera image may not display when the engine is started with a key, due to a design error in the audio dis…
NHTSA campaign 24V384000
How do I fix P0136 on a 2022 Honda HR-V?
- Replace the Bank 1 downstream O2 sensor with an OEM part
- Repair damaged downstream sensor wiring
- Clean or replace corroded sensor connector
- Repair upstream exhaust leaks
About the 2020-2024 Honda HR-V
The 2020-2024 Honda HR-V was commonly sold with the following powertrains: 1.8L I4, 2.0L I4. Common trims include LX, Sport, EX, EX-L.
Why P0136 is the catch-all post-cat code
Each O2 sensor has a family of possible codes:
| Code | Meaning |
|---|---|
| P0136 | Generic circuit issue (catch-all) |
| P0137 | Voltage too low (open or short to ground) |
| P0138 | Voltage too high (short to power or rich condition) |
| P0140 | No activity detected (sensor isn’t reporting anything) |
| P0141 | Heater circuit fault |
When the ECM detects a problem that doesn’t fit the more specific patterns, it falls back to P0136. Reading other codes alongside narrows the diagnosis significantly — P0136 alone is much harder to pin down than P0136 + P0140.
What “downstream sensor” actually monitors
The Bank 1 downstream sensor is mounted in the exhaust after the catalytic converter on Bank 1 (the cylinder bank containing cylinder #1). Its main job is catalyst monitoring — comparing its signal to the upstream sensor’s signal to determine whether the catalyst is still scrubbing exhaust gases.
It provides a secondary, slower fuel-trim correction layer on top of upstream-sensor closed-loop control, but it is not the primary fuel feedback. A bad downstream sensor primarily affects emissions monitoring rather than drivability.
OEM vs aftermarket sensors
The downstream sensor’s role is comparison, not raw measurement, so it is slightly less picky about sensor response curve than the upstream. But aftermarket sensors still produce inconsistent results; for $30 more, an OEM Bosch, Denso, or NTK sensor is worth it on a vehicle you plan to keep.