P0136 on a 2017 Ram 1500
Post-Cat O2 Sensor Circuit Fault (Bank 1)
P0136 on a 2017 Ram 1500 indicates post-cat o2 sensor circuit fault (bank 1). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed bank 1 downstream o2 sensor (typically $150–$450). Confirm the root cause before replacing parts.
What does P0136 mean on a 2017 Ram 1500?
P0136 is set when the ECM detects a general circuit fault on the Bank 1 downstream (post-catalyst) oxygen sensor. Unlike the more specific P0137 (low voltage), P0138 (high voltage), or P0140 (no activity), P0136 is the generic circuit code that covers wiring issues, intermittent connection problems, or signals that go outside expected ranges in a way that doesn't fit a more specific fault category.
This guide covers P0136 across the 2015-2019 Ram 1500 generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Ram 1500 with P0136?
In most cases a 2017 Ram 1500 stays drivable for short trips with P0136 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0136 on a 2017 Ram 1500?
- Check Engine Light is illuminated
- Catalyst readiness monitor will not complete
- Possible slight reduction in fuel economy
- Often no drivability symptoms
- Vehicle will fail emissions / smog testing
What causes P0136 on a 2017 Ram 1500?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed Bank 1 downstream O2 sensor | Most common | $150–$450 |
| Damaged sensor wiring (chafed against exhaust) | Common | $80–$350 |
| Corroded O2 sensor connector | Common | $30–$200 |
| Exhaust leak upstream of the downstream sensor | Occasional | $100–$500 |
| Damaged or compressed sensor pigtail from a previous repair | Occasional | $80–$300 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2017 Ram 1500
-
Read all O2-related codes to refine the picture
P0136 alone is generic. With P0137 it points at low voltage specifically; with P0138 at high voltage; with P0140 at no activity at all; with P0141 at the heater. Cross-referencing tells you whether the diagnostic should target wiring, sensor element, or heater.
Tools: Scan tool with full code retrieval
-
Inspect the sensor wiring
Trace the downstream sensor's harness from the sensor body back to the chassis connector. Look for melted insulation (from exhaust contact), chafing against suspension components, or rodent damage. Repair before replacing the sensor.
Tools: Flashlight, Inspection mirror, Wire repair supplies
-
Test the sensor connector
Disconnect and inspect for water intrusion, corrosion, bent pins. Clean with electrical contact cleaner. The downstream connector sits under the vehicle and gets road spray; corrosion is common after a few salt-belt winters.
Tools: Electrical contact cleaner, Magnifying glass
-
Graph the sensor signal
With engine warm and held at 2500 RPM, watch the Bank 1 downstream O2 voltage. A healthy sensor sits relatively steady around 0.6–0.8 V. Rapid switching, signal stuck at one value, or no signal at all confirms a sensor or wiring issue.
Tools: Scan tool with graphing PIDs
-
Verify the bias voltage from the PCM
Disconnect the sensor and key on. The scan tool should still show bias voltage (typically 0.4–0.5 V) at the connector. If not present, the issue is between the connector and the PCM, not the sensor.
Tools: Scan tool, Multimeter
NHTSA complaints & recalls for the 2017 Ram 1500
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Ram 1500. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ram 1500 diagnostics.
- ENGINE 154
- POWER TRAIN 97
- STEERING 215
- ELECTRICAL SYSTEM 102
- SERVICE BRAKES 91
13 active recalls
- ENGINE AND ENGINE COOLING:ENGINE:DIESEL Aug 2020
Chrysler (FCA US LLC) is recalling certain 2014-2018 Ram 1500 and 2014-2016 Jeep Grand Cherokee vehicles equipped with 3.0L diesel engines. The crankshaft position sensor tone wheel may delaminate causing the engine to lose its ability to synchronize the fuel injector pulses and…
NHTSA campaign 20V475000 - LATCHES/LOCKS/LINKAGES:TAILGATE:LATCH May 2019
Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 f…
NHTSA campaign 19V347000 - STRUCTURE:BODY:TAILGATE Jul 2018
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while d…
NHTSA campaign 18V486000 - ELECTRICAL SYSTEM:WIRING May 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger…
NHTSA campaign 18V332000
How do I fix P0136 on a 2017 Ram 1500?
- Replace the Bank 1 downstream O2 sensor with an OEM part
- Repair damaged downstream sensor wiring
- Clean or replace corroded sensor connector
- Repair upstream exhaust leaks
About the 2015-2019 Ram 1500
The 2015-2019 Ram 1500 was commonly sold with the following powertrains: 5.7L HEMI V8, 3.6L V6, 3.0L EcoDiesel V6. Common trims include Tradesman, Big Horn, Laramie, Rebel, Limited.
Why P0136 is the catch-all post-cat code
Each O2 sensor has a family of possible codes:
| Code | Meaning |
|---|---|
| P0136 | Generic circuit issue (catch-all) |
| P0137 | Voltage too low (open or short to ground) |
| P0138 | Voltage too high (short to power or rich condition) |
| P0140 | No activity detected (sensor isn’t reporting anything) |
| P0141 | Heater circuit fault |
When the ECM detects a problem that doesn’t fit the more specific patterns, it falls back to P0136. Reading other codes alongside narrows the diagnosis significantly — P0136 alone is much harder to pin down than P0136 + P0140.
What “downstream sensor” actually monitors
The Bank 1 downstream sensor is mounted in the exhaust after the catalytic converter on Bank 1 (the cylinder bank containing cylinder #1). Its main job is catalyst monitoring — comparing its signal to the upstream sensor’s signal to determine whether the catalyst is still scrubbing exhaust gases.
It provides a secondary, slower fuel-trim correction layer on top of upstream-sensor closed-loop control, but it is not the primary fuel feedback. A bad downstream sensor primarily affects emissions monitoring rather than drivability.
OEM vs aftermarket sensors
The downstream sensor’s role is comparison, not raw measurement, so it is slightly less picky about sensor response curve than the upstream. But aftermarket sensors still produce inconsistent results; for $30 more, an OEM Bosch, Denso, or NTK sensor is worth it on a vehicle you plan to keep.
P0136 on a 2017 Ram 1500: frequently asked questions
What does diagnostic trouble code P0136 mean on a 2017 Ram 1500?
P0136 is set when the ECM detects a general circuit fault on the Bank 1 downstream (post-catalyst) oxygen sensor. Unlike the more specific P0137 (low voltage), P0138 (high voltage), or P0140 (no activity), P0136 is the generic circuit code that covers wiring issues, intermittent connection problems, or signals that go outside expected ranges in a way that doesn't fit a more specific fault category.
What are the symptoms of P0136 on a 2017 Ram 1500?
Check Engine Light is illuminated. Catalyst readiness monitor will not complete. Possible slight reduction in fuel economy. Often no drivability symptoms. Vehicle will fail emissions / smog testing
What causes P0136 on a 2017 Ram 1500?
Failed Bank 1 downstream O2 sensor (most-common). Damaged sensor wiring (chafed against exhaust) (common). Corroded O2 sensor connector (common). Exhaust leak upstream of the downstream sensor (occasional). Damaged or compressed sensor pigtail from a previous repair (occasional). Failed PCM input (rare) (rare)
Is it safe to drive a 2017 Ram 1500 with P0136?
In most cases a 2017 Ram 1500 stays drivable for short trips with P0136 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.