P0136 on a 2012 Honda Odyssey
Post-Cat O2 Sensor Circuit Fault (Bank 1)
P0136 on a 2012 Honda Odyssey indicates post-cat o2 sensor circuit fault (bank 1). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed bank 1 downstream o2 sensor (typically $150–$450). Confirm the root cause before replacing parts.
What does P0136 mean on a 2012 Honda Odyssey?
P0136 is set when the ECM detects a general circuit fault on the Bank 1 downstream (post-catalyst) oxygen sensor. Unlike the more specific P0137 (low voltage), P0138 (high voltage), or P0140 (no activity), P0136 is the generic circuit code that covers wiring issues, intermittent connection problems, or signals that go outside expected ranges in a way that doesn't fit a more specific fault category.
This guide covers P0136 across the 2010-2014 Honda Odyssey generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Honda Odyssey with P0136?
In most cases a 2012 Honda Odyssey stays drivable for short trips with P0136 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0136 on a 2012 Honda Odyssey?
- Check Engine Light is illuminated
- Catalyst readiness monitor will not complete
- Possible slight reduction in fuel economy
- Often no drivability symptoms
- Vehicle will fail emissions / smog testing
What causes P0136 on a 2012 Honda Odyssey?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed Bank 1 downstream O2 sensor | Most common | $150–$450 |
| Damaged sensor wiring (chafed against exhaust) | Common | $80–$350 |
| Corroded O2 sensor connector | Common | $30–$200 |
| Exhaust leak upstream of the downstream sensor | Occasional | $100–$500 |
| Damaged or compressed sensor pigtail from a previous repair | Occasional | $80–$300 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2012 Honda Odyssey
-
Read all O2-related codes to refine the picture
P0136 alone is generic. With P0137 it points at low voltage specifically; with P0138 at high voltage; with P0140 at no activity at all; with P0141 at the heater. Cross-referencing tells you whether the diagnostic should target wiring, sensor element, or heater.
Tools: Scan tool with full code retrieval
-
Inspect the sensor wiring
Trace the downstream sensor's harness from the sensor body back to the chassis connector. Look for melted insulation (from exhaust contact), chafing against suspension components, or rodent damage. Repair before replacing the sensor.
Tools: Flashlight, Inspection mirror, Wire repair supplies
-
Test the sensor connector
Disconnect and inspect for water intrusion, corrosion, bent pins. Clean with electrical contact cleaner. The downstream connector sits under the vehicle and gets road spray; corrosion is common after a few salt-belt winters.
Tools: Electrical contact cleaner, Magnifying glass
-
Graph the sensor signal
With engine warm and held at 2500 RPM, watch the Bank 1 downstream O2 voltage. A healthy sensor sits relatively steady around 0.6–0.8 V. Rapid switching, signal stuck at one value, or no signal at all confirms a sensor or wiring issue.
Tools: Scan tool with graphing PIDs
-
Verify the bias voltage from the PCM
Disconnect the sensor and key on. The scan tool should still show bias voltage (typically 0.4–0.5 V) at the connector. If not present, the issue is between the connector and the PCM, not the sensor.
Tools: Scan tool, Multimeter
NHTSA complaints & recalls for the 2012 Honda Odyssey
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Honda Odyssey. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda Odyssey diagnostics.
- ENGINE 39
- POWER TRAIN 24
- SERVICE BRAKES 60
- ELECTRICAL SYSTEM 33
- STRUCTURE 25
5 active recalls
- SEATS:MID/REAR ASSEMBLY Nov 2017
Honda (American Honda Motor Co.) is recalling certain 2011-2017 Honda Odyssey vehicles. The second row outboard seats can slide sideways to one of two positions. If a seat is placed between either of the two positions when attaching the seat to the vehicle floor, the seat will…
NHTSA campaign 17V725000 - SEATS:MID/REAR ASSEMBLY Dec 2016
Honda (American Honda Motor Co.) is recalling certain model year 2011-2016 Odyssey vehicles manufactured August 17, 2010, to October 1, 2015. The affected vehicles have second row outboard seats that have a release lever that allows the seats to move for easier access to the thi…
NHTSA campaign 16V933000 - SUSPENSION:FRONT Dec 2011
HONDA IS RECALLING CERTAIN MODEL YEAR 2012, ODYSSEY VEHICLES MANUFACTURED FROM OCTOBER 31, 2011, THROUGH NOVEMBER 30, 2011. THE RETENTION NUT FOR THE FRONT RIGHT LOWER SUSPENSION DAMPER BOLT MAY NOT HAVE BEEN TIGHTENED TO THE PROPER TORQUE, POTENTIALLY ALLOWING THE NUT TO LOOSEN…
NHTSA campaign 11V602000 - POWER TRAIN:AUTOMATIC TRANSMISSION Apr 2013
Honda is recalling certain model year 2012-2013 CR-V, Odyssey, and model year 2013 Acura RDX vehicles. During sub-freezing temperatures, the brake-shift interlock blocking mechanism may become slow and allow the gear selector to be moved from the Park position without pressing t…
NHTSA campaign 13V143000
How do I fix P0136 on a 2012 Honda Odyssey?
- Replace the Bank 1 downstream O2 sensor with an OEM part
- Repair damaged downstream sensor wiring
- Clean or replace corroded sensor connector
- Repair upstream exhaust leaks
About the 2010-2014 Honda Odyssey
The 2010-2014 Honda Odyssey was commonly sold with the following powertrains: 3.5L V6. Common trims include LX, EX, EX-L, Touring, Elite.
Why P0136 is the catch-all post-cat code
Each O2 sensor has a family of possible codes:
| Code | Meaning |
|---|---|
| P0136 | Generic circuit issue (catch-all) |
| P0137 | Voltage too low (open or short to ground) |
| P0138 | Voltage too high (short to power or rich condition) |
| P0140 | No activity detected (sensor isn’t reporting anything) |
| P0141 | Heater circuit fault |
When the ECM detects a problem that doesn’t fit the more specific patterns, it falls back to P0136. Reading other codes alongside narrows the diagnosis significantly — P0136 alone is much harder to pin down than P0136 + P0140.
What “downstream sensor” actually monitors
The Bank 1 downstream sensor is mounted in the exhaust after the catalytic converter on Bank 1 (the cylinder bank containing cylinder #1). Its main job is catalyst monitoring — comparing its signal to the upstream sensor’s signal to determine whether the catalyst is still scrubbing exhaust gases.
It provides a secondary, slower fuel-trim correction layer on top of upstream-sensor closed-loop control, but it is not the primary fuel feedback. A bad downstream sensor primarily affects emissions monitoring rather than drivability.
OEM vs aftermarket sensors
The downstream sensor’s role is comparison, not raw measurement, so it is slightly less picky about sensor response curve than the upstream. But aftermarket sensors still produce inconsistent results; for $30 more, an OEM Bosch, Denso, or NTK sensor is worth it on a vehicle you plan to keep.
P0136 on a 2012 Honda Odyssey: frequently asked questions
What does diagnostic trouble code P0136 mean on a 2012 Honda Odyssey?
P0136 is set when the ECM detects a general circuit fault on the Bank 1 downstream (post-catalyst) oxygen sensor. Unlike the more specific P0137 (low voltage), P0138 (high voltage), or P0140 (no activity), P0136 is the generic circuit code that covers wiring issues, intermittent connection problems, or signals that go outside expected ranges in a way that doesn't fit a more specific fault category.
What are the symptoms of P0136 on a 2012 Honda Odyssey?
Check Engine Light is illuminated. Catalyst readiness monitor will not complete. Possible slight reduction in fuel economy. Often no drivability symptoms. Vehicle will fail emissions / smog testing
What causes P0136 on a 2012 Honda Odyssey?
Failed Bank 1 downstream O2 sensor (most-common). Damaged sensor wiring (chafed against exhaust) (common). Corroded O2 sensor connector (common). Exhaust leak upstream of the downstream sensor (occasional). Damaged or compressed sensor pigtail from a previous repair (occasional). Failed PCM input (rare) (rare)
Is it safe to drive a 2012 Honda Odyssey with P0136?
In most cases a 2012 Honda Odyssey stays drivable for short trips with P0136 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.