P0135 on a 2012 Jeep Wrangler
O2 Sensor Heater Circuit (Bank 1 Upstream)
P0135 on a 2012 Jeep Wrangler indicates o2 sensor heater circuit (bank 1 upstream). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed o2 sensor heater element (open or shorted internally) (typically $150–$450). Confirm the root cause before replacing parts.
What does P0135 mean on a 2012 Jeep Wrangler?
P0135 is set when the ECM detects that the heater element built into the Bank 1 upstream oxygen sensor is not drawing the expected current when commanded on. Zirconium O2 sensors only produce a usable signal above approximately 350 °C / 660 °F, so they include an internal heater that brings them to operating temperature quickly after cold start. P0135 means that heater is open, shorted, or being under-powered.
This guide covers P0135 across the 2010-2014 Jeep Wrangler generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Jeep Wrangler with P0135?
In most cases a 2012 Jeep Wrangler stays drivable for short trips with P0135 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0135 on a 2012 Jeep Wrangler?
- Check Engine Light is illuminated
- Extended open-loop fuel-trim period after cold start (worse fuel economy until warm)
- Slow O2 sensor switching that may take several minutes to begin after cold start
- Possible drivability symptoms if the engine remains in open loop too long
- Vehicle may fail emissions / smog test
What causes P0135 on a 2012 Jeep Wrangler?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed O2 sensor heater element (open or shorted internally) | Most common | $150–$450 |
| Blown O2 heater fuse Always check the fuse before condemning the sensor. | Common | $5–$30 |
| Damaged sensor wiring (chafed against exhaust) | Common | $80–$350 |
| Corroded O2 sensor connector | Common | $30–$200 |
| Failed O2 heater relay (on vehicles with one) | Occasional | $30–$150 |
| Failed PCM driver for the heater circuit (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2012 Jeep Wrangler
-
Check the O2 heater fuse first
Most vehicles route O2 heater power through a dedicated fuse, usually labeled "O2H" or "O2 SNSR" in the underhood fuse box. Replace any blown fuse with the exact amperage rating. If the fuse blows again immediately, the heater or its wiring is shorted.
Tools: Replacement fuse, Fuse puller
-
Measure heater resistance at the sensor
Unplug the Bank 1 upstream O2 sensor. Measure resistance across the heater terminals (typically the two same-color wires — consult the wiring diagram). Expected resistance is approximately 3 to 15 Ω cold, depending on the sensor. Infinite resistance means an open heater; near zero means a shorted heater.
Tools: Multimeter, Wiring diagram
-
Verify power and ground at the connector
With the key on and engine running, back-probe the heater power and ground wires. Battery voltage should be present on power and a clean ground on the other side. Missing voltage points to the fuse, the wiring, or the PCM driver.
Tools: Multimeter, Back-probe pins
-
Measure heater current draw
A working heater draws approximately 0.8 to 2 A depending on sensor design. Use a low-current clamp around the heater wire, or a multimeter in series. Current of 0 A with voltage present means the heater is open. Current well above 2 A means the heater is partially shorted and will fail soon.
Tools: Multimeter with current function, Low-current clamp (preferred)
-
Inspect the sensor and its wiring for physical damage
O2 sensor harnesses run close to hot exhaust components and are a common chafing victim. Inspect the wiring from the connector to the sensor body. Heat-damaged insulation, melted plastic, or visible copper requires harness repair or replacement, not just a new sensor.
Tools: Flashlight, Wire repair supplies
NHTSA complaints & recalls for the 2012 Jeep Wrangler
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Jeep Wrangler. Use these to gauge how common a problem is on your specific vehicle before you start chasing Jeep Wrangler diagnostics.
- POWER TRAIN 282
- ENGINE 171
- STEERING 204
- ELECTRICAL SYSTEM 147
- AIR BAGS 128
10 active recalls
- AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jan 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal…
NHTSA campaign 19V018000 - SEAT BELTS:FRONT:ANCHORAGE Sep 2019
Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.…
NHTSA campaign 19V680000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jan 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, Sou…
NHTSA campaign 18V021000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE May 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM…
NHTSA campaign 16V352000
How do I fix P0135 on a 2012 Jeep Wrangler?
- Replace the Bank 1 upstream O2 sensor with an OEM part
- Replace the O2 heater fuse
- Repair damaged O2 sensor wiring
- Replace the O2 heater relay
- Clean or repair the O2 sensor connector
About the 2010-2014 Jeep Wrangler
The 2010-2014 Jeep Wrangler was commonly sold with the following powertrains: 3.6L Pentastar V6, 2.0L Turbo I4, 3.0L EcoDiesel V6. Common trims include Sport, Sport S, Sahara, Rubicon.
Why heater failure matters
Zirconium O2 sensors produce no usable signal until they reach about 350 °C. Without the heater, the sensor waits for exhaust heat to bring it up to temperature — which can take 5+ minutes of driving. During that period the ECM runs in “open loop” mode, using a calibrated fueling map rather than O2 feedback. This is fine briefly but causes poor cold-running emissions and 10–20 % worse fuel economy while the heater is dead.
P0135 with the sensor only weeks old
Aftermarket O2 sensors fail at much higher rates than OEM. If P0135 appeared shortly after an O2 sensor replacement with a non-OEM part, the new sensor itself is the most likely problem. Warranty-exchange for an OEM-equivalent before chasing the wiring.
Heater current and the “weak heater”
A heater that draws low current but is not fully open is a “weak” heater. It will warm the sensor partially, allowing the sensor to work but slowly. The ECM eventually sets P0135 even though the heater is not fully dead. A current measurement is the only reliable way to catch this failure mode — a simple resistance check often misses it.
P0135 on a 2012 Jeep Wrangler: frequently asked questions
What does diagnostic trouble code P0135 mean on a 2012 Jeep Wrangler?
P0135 is set when the ECM detects that the heater element built into the Bank 1 upstream oxygen sensor is not drawing the expected current when commanded on. Zirconium O2 sensors only produce a usable signal above approximately 350 °C / 660 °F, so they include an internal heater that brings them to operating temperature quickly after cold start. P0135 means that heater is open, shorted, or being under-powered.
What are the symptoms of P0135 on a 2012 Jeep Wrangler?
Check Engine Light is illuminated. Extended open-loop fuel-trim period after cold start (worse fuel economy until warm). Slow O2 sensor switching that may take several minutes to begin after cold start. Possible drivability symptoms if the engine remains in open loop too long. Vehicle may fail emissions / smog test
What causes P0135 on a 2012 Jeep Wrangler?
Failed O2 sensor heater element (open or shorted internally) (most-common). Blown O2 heater fuse (common). Damaged sensor wiring (chafed against exhaust) (common). Corroded O2 sensor connector (common). Failed O2 heater relay (on vehicles with one) (occasional). Failed PCM driver for the heater circuit (rare) (rare)
Is it safe to drive a 2012 Jeep Wrangler with P0135?
In most cases a 2012 Jeep Wrangler stays drivable for short trips with P0135 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.