P0118 on a 2017 Chevrolet Malibu
Coolant Temp Sensor High Input
P0118 on a 2017 Chevrolet Malibu indicates coolant temp sensor high input. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is disconnected or unlatched ect sensor connector (typically $0–$50). Confirm the root cause before replacing parts.
What does P0118 mean on a 2017 Chevrolet Malibu?
P0118 is set when the engine control module reads the engine coolant temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold coolant temperature (often −40 °F / −40 °C). This is the open-circuit fingerprint for the ECT sensor: a disconnected sensor, a broken signal wire, or a sensor failed open internally.
This guide covers P0118 across the 2015-2019 Chevrolet Malibu generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Chevrolet Malibu with P0118?
In most cases a 2017 Chevrolet Malibu stays drivable for short trips with P0118 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0118 on a 2017 Chevrolet Malibu?
- Check Engine Light is illuminated
- Temperature gauge reads zero or stays cold
- Difficult cold start with rich-running symptoms
- Cooling fans may run constantly (ECM thinks coolant is dangerously cold)
- Slightly reduced fuel economy
- Cold-running engine doesn't warm up properly per the gauge
- Possible hard start when the engine is hot (ECM commands cold-start enrichment)
What causes P0118 on a 2017 Chevrolet Malibu?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected or unlatched ECT sensor connector | Most common | $0–$50 |
| Broken or chafed ECT signal wire (open circuit) | Common | $80–$350 |
| Internally failed ECT sensor (element opened) | Common | $30–$200 |
| Corroded sensor connector pins | Common | $30–$200 |
| Damaged sensor body from coolant leak or freeze | Occasional | $50–$250 |
| Failed PCM signal input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2017 Chevrolet Malibu
-
Read ECT temperature with a scan tool
A working ECT reads close to ambient air temperature when the engine has been off long enough to cool. A reading of "−40 °F" or "−40 °C" is the classic open-circuit fingerprint.
Tools: Scan tool with ECT PID
-
Inspect the connector and visible wiring
Locate the ECT sensor (usually threaded into the intake manifold or thermostat housing). Unplug, inspect for corrosion, water, bent pins. Re-seat and clear the code — if it stays clear, the connector was the problem.
Tools: Electrical contact cleaner, Flashlight
-
Bench-test the ECT sensor resistance
Remove the sensor (place a rag — coolant will drip). Measure resistance across its terminals at room temperature. Compare to the service manual — most NTC ECTs read 2.0–4.5 kΩ at 68 °F (20 °C). Infinite resistance means the sensor is open and needs replacement.
Tools: Multimeter, Service spec sheet, Coolant catch and replacement
-
Verify signal-wire continuity to the PCM
With the ECT disconnected, check continuity from the sensor's signal wire to the corresponding PCM pin. Open circuit confirms a broken wire somewhere along the path. Visual inspection of the harness — particularly where it routes near hot exhaust or moving accessories — often reveals the chafe point.
Tools: Multimeter, Wiring diagram
-
Jumper-test the signal wire
With the ECT disconnected, briefly jumper the signal wire to ground and observe the scan tool — the reading should swing from "very cold" to "very hot." No swing points at the wiring or PCM input rather than the sensor.
Tools: Jumper wire, Scan tool
NHTSA complaints & recalls for the 2017 Chevrolet Malibu
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Chevrolet Malibu. Use these to gauge how common a problem is on your specific vehicle before you start chasing Chevrolet Malibu diagnostics.
- ENGINE 253
- POWER TRAIN 141
- VEHICLE SPEED CONTROL 136
- ELECTRICAL SYSTEM 169
- UNKNOWN OR OTHER 148
4 active recalls
- AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION Jun 2018
General Motors LLC (GM) is recalling certain 2016-2018 Chevrolet Malibu vehicles. During servicing, a Passenger Presence System (PPS) may have been installed that was not correctly calibrated to the vehicle's seat type. As a result, the PPS may not properly identify an adult pa…
NHTSA campaign 18V400000 - FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP May 2018
General Motors LLC (GM) is recalling certain 2015-2018 GMC Canyon, 2016-2017 Buick Envision, 2016-2018 Chevrolet Colorado and Malibu, 2017-2018 GMC Acadia, 2018 Buick LaCrosse, Cadillac ATS, Chevrolet Equinox, and GMC Terrain vehicles. The high pressure fuel pump may detach from…
NHTSA campaign 18V358000 - AIR BAGS:SIDE/WINDOW Dec 2016
General Motors LLC (GM) is recalling certain 2017 Malibu vehicles manufactured on November 10, 2016. The right-hand rear side air bag inflator manifold may have insufficient welds.…
NHTSA campaign 16V870000 - SEAT BELTS:CRITICAL FASTENERS Aug 2021
General Motors, LLC (GM) is recalling certain 2016-2021 Chevrolet Malibu and 2019-2021 Cadillac XT4 vehicles. The rear seat belt retractors may be improperly secured with loose or missing fasteners.…
NHTSA campaign 21V649000
How do I fix P0118 on a 2017 Chevrolet Malibu?
- Reconnect the ECT sensor connector
- Replace the ECT sensor with an OEM part
- Repair the broken ECT signal wire
- Clean corroded connector pins
About the 2015-2019 Chevrolet Malibu
The 2015-2019 Chevrolet Malibu was commonly sold with the following powertrains: 1.5L Turbo I4, 2.0L Turbo I4, 2.5L I4, 1.8L Hybrid I4. Common trims include L, LS, RS, LT, Premier.
P0118 vs P0117
These are the two ends of the same circuit:
- P0117 — ECT signal too low (sensor reads very high temperature like “300 °F”). Usually a shorted-to-ground wire or sensor failed closed.
- P0118 — ECT signal too high (sensor reads very low temperature like “−40 °F”). Usually an open circuit — disconnected, broken wire, or sensor open internally.
Why P0118 causes a hot engine to run rich
When the ECT signal goes missing or reads “very cold,” the ECM commands cold-start enrichment continuously — even on a hot engine. The result: fouled spark plugs, rich-running symptoms, possibly a hard start when the engine is actually warm because flooding occurs. This is why P0118 is worth fixing promptly even though it doesn’t look like a serious code.
Multi-sensor confusion: ECT vs IAT vs CHT
Modern engines may have multiple temperature sensors:
- ECT (Engine Coolant Temperature) — in coolant passage
- IAT (Intake Air Temperature) — in air intake tract
- CHT (Cylinder Head Temperature) — bolted to head, no coolant contact
- TFT (Transmission Fluid Temperature) — in transmission
Their codes are similar — P0118 (ECT high), P0113 (IAT high), P0119 (ECT erratic). Make sure the connector you are pulling is for the sensor referenced in the code.
P0118 on a 2017 Chevrolet Malibu: frequently asked questions
What does diagnostic trouble code P0118 mean on a 2017 Chevrolet Malibu?
P0118 is set when the engine control module reads the engine coolant temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold coolant temperature (often −40 °F / −40 °C). This is the open-circuit fingerprint for the ECT sensor: a disconnected sensor, a broken signal wire, or a sensor failed open internally.
What are the symptoms of P0118 on a 2017 Chevrolet Malibu?
Check Engine Light is illuminated. Temperature gauge reads zero or stays cold. Difficult cold start with rich-running symptoms. Cooling fans may run constantly (ECM thinks coolant is dangerously cold). Slightly reduced fuel economy. Cold-running engine doesn't warm up properly per the gauge. Possible hard start when the engine is hot (ECM commands cold-start enrichment)
What causes P0118 on a 2017 Chevrolet Malibu?
Disconnected or unlatched ECT sensor connector (most-common). Broken or chafed ECT signal wire (open circuit) (common). Internally failed ECT sensor (element opened) (common). Corroded sensor connector pins (common). Damaged sensor body from coolant leak or freeze (occasional). Failed PCM signal input (rare) (rare)
Is it safe to drive a 2017 Chevrolet Malibu with P0118?
In most cases a 2017 Chevrolet Malibu stays drivable for short trips with P0118 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.