P0113 on Ford vehicles
Intake Air Temperature High Input — what it means on a Ford, whether it's safe to drive, and the fixes by model and year.
P0113 on a Ford means intake air temperature high input. Most vehicles stay drivable short-term, but diagnose it promptly. The most common cause is disconnected or unlatched iat / maf-iat connector (typically $0–$50). Pick your Ford model below for its known failure patterns, recalls, and TSBs.
What does P0113 mean on a Ford?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element.
P0113 is a standardized OBD-II code, so its definition is the same on every Ford. What differs by model and engine is which cause is most likely — pick your Ford model below for a diagnosis tuned to its known failure patterns, recalls, and TSBs.
Is it safe to drive a Ford with P0113?
In most cases a Ford stays drivable for short trips with P0113 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test. Exact tolerance depends on the model and engine.
What causes P0113 on a Ford?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected or unlatched IAT / MAF-IAT connector | Most common | $0–$50 |
| Open circuit in the IAT signal wire (broken, chafed, or pinched) | Common | $80–$350 |
| Failed IAT sensor element (open internally) | Common | $30–$150 |
| Corroded sensor connector pins | Common | $30–$200 |
| Damaged sensor body from intake backfire | Occasional | $30–$200 |
| Failed PCM input (extremely rare) | Rare | $400–$1,500 |
Repair costs are typical US ranges and vary by Ford model, model year, and labor rate. A diagnostic trouble code is a symptom, not a guaranteed failed part — confirm the root cause before replacing anything.
P0113 by Ford model
Select your Ford model and year for a P0113 diagnosis tuned to that vehicle's failure patterns, recalls, and TSBs.
Ford F-150
43 recalls on record across the years covered below.
Ford Escape
3,364 NHTSA owner complaints · 24 recalls on record across the years covered below.
Ford Explorer
2,694 NHTSA owner complaints · 43 recalls on record across the years covered below.
Ford Bronco
328 NHTSA owner complaints · 21 recalls on record across the years covered below.
Ford Mustang
771 NHTSA owner complaints · 22 recalls on record across the years covered below.
Complaint and recall counts are NHTSA totals for the model years covered on this site, not counts specific to P0113.
P0113 on other makes
Other codes on Ford vehicles
P0113 on a Ford: frequently asked questions
What does diagnostic trouble code P0113 mean on a Ford?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element. P0113 is a standardized OBD-II code, so the definition is the same on every Ford — which cause is most likely varies by model and engine.
What are the symptoms of P0113 on a Ford?
Check Engine Light is illuminated. Slightly harder cold starting in some cases. Mild reduction in fuel economy. Reduced power under hard acceleration (engine adds extra fuel for "cold" air). Often no noticeable drivability problem at all
What causes P0113 on a Ford?
Disconnected or unlatched IAT / MAF-IAT connector (most-common). Open circuit in the IAT signal wire (broken, chafed, or pinched) (common). Failed IAT sensor element (open internally) (common). Corroded sensor connector pins (common). Damaged sensor body from intake backfire (occasional). Failed PCM input (extremely rare) (rare)
Is it safe to drive a Ford with P0113?
In most cases a Ford stays drivable for short trips with P0113 active, but it should be diagnosed and repaired promptly — this is a low-severity code. Ignoring it can lead to further damage or a failed emissions test. Exact tolerance depends on the model and engine.