P0113 on a 2017 Ram 1500
Intake Air Temperature High Input
P0113 on a 2017 Ram 1500 indicates intake air temperature high input. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is disconnected or unlatched iat / maf-iat connector (typically $0–$50). Confirm the root cause before replacing parts.
What does P0113 mean on a 2017 Ram 1500?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element.
This guide covers P0113 across the 2015-2019 Ram 1500 generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Ram 1500 with P0113?
In most cases a 2017 Ram 1500 stays drivable for short trips with P0113 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0113 on a 2017 Ram 1500?
- Check Engine Light is illuminated
- Slightly harder cold starting in some cases
- Mild reduction in fuel economy
- Reduced power under hard acceleration (engine adds extra fuel for "cold" air)
- Often no noticeable drivability problem at all
What causes P0113 on a 2017 Ram 1500?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected or unlatched IAT / MAF-IAT connector | Most common | $0–$50 |
| Open circuit in the IAT signal wire (broken, chafed, or pinched) | Common | $80–$350 |
| Failed IAT sensor element (open internally) | Common | $30–$150 |
| Corroded sensor connector pins | Common | $30–$200 |
| Damaged sensor body from intake backfire | Occasional | $30–$200 |
| Failed PCM input (extremely rare) | Rare | $400–$1,500 |
How to diagnose this on a 2017 Ram 1500
-
Confirm where the IAT sensor lives on this engine
Modern engines fall into two configurations: a standalone IAT sensor in the air intake tract, or a combined MAF/IAT assembly where the IAT element is built into the mass airflow housing. Both share P0113 — the diagnostic difference is where to find the connector and which wires carry the IAT signal.
Tools: Vehicle-specific service information
-
Read IAT temperature on the scan tool
A working IAT reads close to ambient air temperature when the engine has been off long enough to cool. Compare to the coolant temperature reading at cold start — they should agree within a few degrees. An IAT reading of "−40 °F" or "−40 °C" is the classic open-circuit fingerprint.
Tools: Scan tool with IAT PID
-
Inspect the connector and wiring
Unplug the IAT connector and inspect for corrosion, water, or bent pins. With the connector unplugged and the key on, the scan tool should still report a fixed "very cold" value — that confirms an open circuit signature is what set the code.
Tools: Electrical contact cleaner, Flashlight
-
Bench-test the IAT sensor with a multimeter
With the sensor removed, measure resistance across its terminals at room temperature. Compare to the service manual — most NTC IAT sensors read 2.0–4.5 kΩ at 68 °F (20 °C). Infinite resistance means the sensor is open and dead. Heating the sensor gently should cause resistance to drop.
Tools: Multimeter, Heat gun or hair dryer (optional), Service spec sheet
-
Jumper test the signal wire
With the IAT disconnected, briefly jumper the signal wire to ground and observe the scan tool reading — it should swing from "very cold" to "very hot" (P0112 territory). If the reading does not change, the wiring or PCM input is at fault rather than the sensor.
Tools: Jumper wire, Scan tool
NHTSA complaints & recalls for the 2017 Ram 1500
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Ram 1500. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ram 1500 diagnostics.
- ENGINE 154
- POWER TRAIN 97
- STEERING 215
- ELECTRICAL SYSTEM 102
- SERVICE BRAKES 91
13 active recalls
- ENGINE AND ENGINE COOLING:ENGINE:DIESEL Aug 2020
Chrysler (FCA US LLC) is recalling certain 2014-2018 Ram 1500 and 2014-2016 Jeep Grand Cherokee vehicles equipped with 3.0L diesel engines. The crankshaft position sensor tone wheel may delaminate causing the engine to lose its ability to synchronize the fuel injector pulses and…
NHTSA campaign 20V475000 - LATCHES/LOCKS/LINKAGES:TAILGATE:LATCH May 2019
Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 f…
NHTSA campaign 19V347000 - STRUCTURE:BODY:TAILGATE Jul 2018
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while d…
NHTSA campaign 18V486000 - ELECTRICAL SYSTEM:WIRING May 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger…
NHTSA campaign 18V332000
How do I fix P0113 on a 2017 Ram 1500?
- Reconnect the IAT or MAF-IAT connector
- Replace the IAT sensor (standalone) or the MAF/IAT assembly
- Repair broken IAT signal wire
- Clean corroded sensor connector pins
About the 2015-2019 Ram 1500
The 2015-2019 Ram 1500 was commonly sold with the following powertrains: 5.7L HEMI V8, 3.6L V6, 3.0L EcoDiesel V6. Common trims include Tradesman, Big Horn, Laramie, Rebel, Limited.
P0113 vs P0112
These are the two ends of the same circuit:
- P0112 — IAT signal reads too low (sensor sees a very high temperature, often “300 °F”). Usually a shorted-to-ground signal wire or a sensor failed in the closed direction.
- P0113 — IAT signal reads too high (sensor sees a very low temperature, often “−40 °F”). Usually an open circuit — disconnected, broken wire, or sensor open internally.
Why P0113 rarely affects drivability
Modern ECMs use the IAT for relatively minor fuel-trim corrections and to fine-tune cold-start enrichment. With a missing IAT signal, the ECM uses a default value (usually around 70 °F) and the engine runs essentially normally. This is why many drivers report P0113 with no symptoms at all beyond the Check Engine Light.
Combined MAF/IAT assemblies
On most modern vehicles the IAT is integrated into the MAF housing as a single assembly. When the IAT element fails, the entire MAF assembly must be replaced — there is no separate IAT to service. Confirm the part number before ordering; combined assemblies are 4–10× the cost of a standalone IAT.
P0113 on a 2017 Ram 1500: frequently asked questions
What does diagnostic trouble code P0113 mean on a 2017 Ram 1500?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element.
What are the symptoms of P0113 on a 2017 Ram 1500?
Check Engine Light is illuminated. Slightly harder cold starting in some cases. Mild reduction in fuel economy. Reduced power under hard acceleration (engine adds extra fuel for "cold" air). Often no noticeable drivability problem at all
What causes P0113 on a 2017 Ram 1500?
Disconnected or unlatched IAT / MAF-IAT connector (most-common). Open circuit in the IAT signal wire (broken, chafed, or pinched) (common). Failed IAT sensor element (open internally) (common). Corroded sensor connector pins (common). Damaged sensor body from intake backfire (occasional). Failed PCM input (extremely rare) (rare)
Is it safe to drive a 2017 Ram 1500 with P0113?
In most cases a 2017 Ram 1500 stays drivable for short trips with P0113 active, but it should be diagnosed and repaired promptly — this is a low-severity code. Ignoring it can lead to further damage or a failed emissions test.