P0102 on a 2017 Chevrolet Trax
MAF Sensor Low Input
P0102 on a 2017 Chevrolet Trax indicates maf sensor low input. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is disconnected maf sensor connector (typically $0–$50). Confirm the root cause before replacing parts.
What does P0102 mean on a 2017 Chevrolet Trax?
P0102 is set when the ECM sees the mass air flow sensor signal at a voltage or frequency below the calibrated minimum for the engine's operating conditions. Where P0101 means "MAF reading is implausible", P0102 means "MAF signal is too low or missing entirely." The cause is usually a disconnected sensor, broken signal wire, or a sensor that has failed in a way that produces no output.
This guide covers P0102 across the 2015-2019 Chevrolet Trax generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Chevrolet Trax with P0102?
In most cases a 2017 Chevrolet Trax stays drivable for short trips with P0102 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0102 on a 2017 Chevrolet Trax?
- Check Engine Light is illuminated
- Hesitation, stumble, or stall on acceleration
- Hard starting or extended crank time
- Reduced power and throttle response
- Black smoke or rich smell from exhaust (ECM defaults to a rich limp map)
- Reduced fuel economy
What causes P0102 on a 2017 Chevrolet Trax?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected MAF sensor connector Check this first — the simplest cause is the most common after recent work. | Most common | $0–$50 |
| Broken or shorted MAF signal wire | Common | $80–$350 |
| Corroded MAF sensor connector pins | Common | $30–$200 |
| Internal MAF sensor failure (sensor produces no output) | Common | $80–$450 |
| Open in MAF sensor 5 V reference or ground supply | Occasional | $100–$400 |
| Failed PCM input circuit for the MAF (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2017 Chevrolet Trax
-
Verify the MAF connector is fully seated
A loose or unlatched MAF connector is the #1 cause of P0102 after recent under-hood work — air filter changes, intake cleaning, or a previous diagnostic. Press the connector firmly until the latch clicks. Clear the code and drive.
Tools: None
-
Read MAF signal voltage or frequency
On a standard hot-wire MAF, the signal should read about 0.6 V at key-on engine-off and climb to 1.5–2.5 V at idle. A stuck reading below 0.3 V at idle confirms a low-input fault. On digital MAFs the scan tool will report frequency in Hz instead — typical idle readings are 2.5–3.5 kHz.
Tools: Scan tool with MAF voltage / frequency PID, Multimeter (back-probe capable)
-
Test the MAF power, ground, and signal wires
Back-probe the MAF connector with a multimeter. Verify: battery voltage on the supply wire with key on, continuity from the ground wire to engine ground, and an open or short on the signal wire to the PCM. A missing supply voltage points to a blown fuse or harness fault.
Tools: Multimeter, Back-probe pins, Wiring diagram
-
Inspect the connector pins
Unplug the MAF and look closely at the pins inside the connector. Green corrosion, bent terminals, or evidence of water intrusion will cause intermittent or low signal. Clean with electrical contact cleaner and bend terminals straight if needed.
Tools: Electrical contact cleaner, Pick tool, Magnifying glass
-
Swap or test the MAF sensor
If wiring and power supply test good and the connector is clean, the MAF sensor is the prime suspect. Swap with a known-good unit if available, or install a new OEM sensor. Avoid the cheap eBay MAFs — they fail at very high rates.
Tools: Socket / driver to remove MAF
NHTSA complaints & recalls for the 2017 Chevrolet Trax
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Chevrolet Trax. Use these to gauge how common a problem is on your specific vehicle before you start chasing Chevrolet Trax diagnostics.
- ENGINE 40
- ELECTRICAL SYSTEM 24
- UNKNOWN OR OTHER 22
- STEERING 19
- SUSPENSION 10
3 active recalls
- SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT Apr 2019
General Motors LLC (GM) is recalling certain 2017-2019 Chevrolet Trax vehicles. A joint in one or both of the front lower-control arms may have been improperly welded. An improperly welded joint may break, resulting in the partial separation of the lower-control arm from the ve…
NHTSA campaign 19V312000 - SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT Sep 2019
General Motors LLC (GM) is recalling certain 2015-2018 Chevrolet Trax vehicles. A joint in one or both of the front lower control arms may have been improperly welded. An improperly welded joint may break, resulting in the partial separation of the lower control arm from the vehi…
NHTSA campaign 19V652000 - AIR BAGS:FRONTAL Sep 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500…
NHTSA campaign 16V651000
How do I fix P0102 on a 2017 Chevrolet Trax?
- Reconnect the MAF sensor connector
- Replace the MAF sensor with an OEM unit
- Repair broken signal, power, or ground wires
- Clean or replace corroded connector terminals
About the 2015-2019 Chevrolet Trax
The 2015-2019 Chevrolet Trax was commonly sold with the following powertrains: 1.4L Turbo I4, 1.2L Turbo I3. Common trims include LS, 1RS, LT, 2RS, Activ.
P0102 vs P0101
These are different failure modes on the same sensor:
- P0102 — Signal is too low or missing. Usually a wiring, connector, or dead-sensor problem. Cannot be solved by cleaning.
- P0101 — Signal is present but does not match expected airflow. Usually a dirty sensor or an intake leak. Cleaning often resolves it.
What the engine does when the MAF signal is missing
Without a usable MAF reading, the ECM falls back to “speed-density” mode — it estimates airflow from RPM, throttle position, and intake-air temperature. This works but is less precise. Expect noticeably worse fuel economy and hesitation while the code is active. The car remains drivable but is operating on a calibrated backup map.
Counterfeit MAF sensors
The aftermarket MAF market is full of counterfeit Bosch, Hitachi, and Denso sensors sold at suspiciously low prices on Amazon and eBay. Counterfeits often work briefly then set P0102 again within weeks. For the small price difference, buy from a reputable parts store or a dealer. Genuine OEM MAFs typically last 100,000+ miles.