P0017 on a 2012 Jeep Wrangler
Crank/Cam Correlation (Bank 1 Exhaust)
P0017 on a 2012 Jeep Wrangler indicates crank/cam correlation (bank 1 exhaust). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is stretched timing chain or worn timing chain guides (typically $800–$3,500). Confirm the root cause before replacing parts.
What does P0017 mean on a 2012 Jeep Wrangler?
P0017 is the exhaust-cam counterpart of P0016. The ECM compares the crankshaft position signal to the Bank 1 exhaust camshaft position signal and finds them more than a calibrated number of degrees out of alignment. This usually means timing chain stretch, a stuck cam phaser unable to return to base position, or a position sensor producing bad data. P0017 is one of the strongest indicators of timing chain wear on engines with dual VVT.
This guide covers P0017 across the 2010-2014 Jeep Wrangler generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Jeep Wrangler with P0017?
In most cases a 2012 Jeep Wrangler stays drivable for short trips with P0017 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0017 on a 2012 Jeep Wrangler?
- Check Engine Light is illuminated
- Cold-start rattle or chirp from the front timing cover
- Hard cold start with long crank times
- Loss of low-end torque
- Rough idle and reduced throttle response
- Reduced fuel economy
- Possible engine no-start if timing has slipped enough
What causes P0017 on a 2012 Jeep Wrangler?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Stretched timing chain or worn timing chain guides | Most common | $800–$3,500 |
| Stuck exhaust cam phaser cannot return to base timing | Common | $400–$1,500 |
| Failed exhaust cam position sensor producing inaccurate readings | Common | $100–$400 |
| Low oil pressure preventing the phaser from holding position | Occasional | $50–$200 |
| Damaged exhaust cam reluctor wheel or tone ring | Occasional | $300–$1,500 |
| Stuck-open exhaust VVT oil control valve | Occasional | $100–$450 |
| Timing chain skipped one tooth after a tensioner failure | Rare | $1,000–$4,000 |
How to diagnose this on a 2012 Jeep Wrangler
-
Check oil level and pressure
P0017 with low oil pressure is the exhaust phaser unable to hold commanded position. Confirm level on level ground with a warm engine and measure oil pressure with a mechanical gauge before replacing parts.
Tools: Dipstick, Mechanical oil pressure gauge
-
Watch exhaust cam vs. crank position in live data
The cam-crank offset should remain fixed. An offset that drifts as RPM rises indicates timing chain stretch. A static but wrong offset can mean the chain jumped a tooth. Compare to service-manual specifications.
Tools: Scan tool with dual position PIDs
-
Listen for chain noise at cold start
A 1–3 second cold-start rattle that quiets as oil pressure builds is early chain wear. Continuous rattle indicates advanced wear with imminent failure risk. Use a mechanic's stethoscope on the front timing cover.
Tools: Mechanic's stethoscope
-
Test the exhaust cam sensor electrically
Disconnect the sensor and inspect the connector. With a scope, check the signal pattern — should be a clean square wave with no missing pulses. A noisy or absent signal sets P0017 even with a perfect chain.
Tools: Oscilloscope or scan tool with raw sensor PIDs, Multimeter
-
Inspect the cam phaser on engines with documented failures
On Ford 5.4 3V Triton, GM 3.6 LFX/LLT, BMW N20/N26, and VW EA888 engines, the exhaust phaser is a common P0017 cause independent of chain wear. A scope on the cam sensor while bidirectionally commanding the OCV will show whether the phaser is responding.
Tools: Bidirectional scan tool, Oscilloscope (optional)
NHTSA complaints & recalls for the 2012 Jeep Wrangler
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Jeep Wrangler. Use these to gauge how common a problem is on your specific vehicle before you start chasing Jeep Wrangler diagnostics.
- POWER TRAIN 282
- ENGINE 171
- STEERING 204
- ELECTRICAL SYSTEM 147
- AIR BAGS 128
10 active recalls
- AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jan 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal…
NHTSA campaign 19V018000 - SEAT BELTS:FRONT:ANCHORAGE Sep 2019
Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.…
NHTSA campaign 19V680000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jan 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, Sou…
NHTSA campaign 18V021000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE May 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM…
NHTSA campaign 16V352000
How do I fix P0017 on a 2012 Jeep Wrangler?
- Replace timing chain, guides, tensioner, and sprockets as a complete kit
- Replace the exhaust cam phaser / VVT actuator
- Replace the exhaust cam position sensor
- Service or replace the exhaust-side VVT oil control valve
- Address any underlying oil pressure or sludge issue
About the 2010-2014 Jeep Wrangler
The 2010-2014 Jeep Wrangler was commonly sold with the following powertrains: 3.6L Pentastar V6, 2.0L Turbo I4, 3.0L EcoDiesel V6. Common trims include Sport, Sport S, Sahara, Rubicon.
P0017 on chain-stretch-prone engines
P0017 on these engines should be assumed to be a timing chain problem until proven otherwise — they all have documented chain wear issues:
- GM 3.6 LFX / LLT / LF1 — chain stretch around 80–120k miles
- BMW N20 / N26 2.0T — chronic catastrophic chain failure
- VW / Audi EA888 Gen 1 + 2 — chain stretch at 80–100k
- Ford 5.4 3V Triton V8 — combined phaser and chain failure
- Hyundai / Kia Theta II 2.4 — chain and tensioner failure
On these engines, replace the chain as a complete kit (chain, guides, tensioner, sprockets). Half-replacing leads to repeat failure within 30–50k miles.
Why ignoring P0017 risks engine destruction
The progression of timing chain wear on these engines is:
- P0017 sets intermittently — chain has stretched enough to drift
- P0017 sets every drive cycle — wear is consistent
- Chain rattle becomes audible from the cab
- Chain skips a tooth — valves contact pistons on interference engines
- Engine destroyed — bent valves, possibly damaged head and pistons
The repair bill jumps from $1,500–$3,500 (timing job) at step 2 to $4,000–$10,000+ (rebuilt head or new engine) at step 5. P0017 on a known-affected engine should be fixed within weeks.
P0017 vs P0016
- P0016 — Bank 1 intake cam correlation off
- P0017 — Bank 1 exhaust cam correlation off
Both setting together is strong evidence of timing chain wear since the chain affects both cams equally. Just one bank or one cam setting alone is more likely a single phaser or sensor.
P0017 on a 2012 Jeep Wrangler: frequently asked questions
What does diagnostic trouble code P0017 mean on a 2012 Jeep Wrangler?
P0017 is the exhaust-cam counterpart of P0016. The ECM compares the crankshaft position signal to the Bank 1 exhaust camshaft position signal and finds them more than a calibrated number of degrees out of alignment. This usually means timing chain stretch, a stuck cam phaser unable to return to base position, or a position sensor producing bad data. P0017 is one of the strongest indicators of timing chain wear on engines with dual VVT.
What are the symptoms of P0017 on a 2012 Jeep Wrangler?
Check Engine Light is illuminated. Cold-start rattle or chirp from the front timing cover. Hard cold start with long crank times. Loss of low-end torque. Rough idle and reduced throttle response. Reduced fuel economy. Possible engine no-start if timing has slipped enough
What causes P0017 on a 2012 Jeep Wrangler?
Stretched timing chain or worn timing chain guides (most-common). Stuck exhaust cam phaser cannot return to base timing (common). Failed exhaust cam position sensor producing inaccurate readings (common). Low oil pressure preventing the phaser from holding position (occasional). Damaged exhaust cam reluctor wheel or tone ring (occasional). Stuck-open exhaust VVT oil control valve (occasional). Timing chain skipped one tooth after a tensioner failure (rare)
Is it safe to drive a 2012 Jeep Wrangler with P0017?
In most cases a 2012 Jeep Wrangler stays drivable for short trips with P0017 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.