P0012 on a 2022 GMC Sierra 1500
Intake Cam Over-Retarded (Bank 1, VVT)
P0012 on a 2022 GMC Sierra 1500 indicates intake cam over-retarded (bank 1, vvt). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is stuck-closed vvt oil control valve (cannot direct oil to advance the cam) (typically $100–$450). Confirm the root cause before replacing parts.
What does P0012 mean on a 2022 GMC Sierra 1500?
P0012 is set when the engine control module commands the Bank 1 intake camshaft to a specific advance position and the actual cam position remains too retarded — the phaser is stuck in or near its base position instead of advancing as commanded. P0012 is the inverse of P0011; both point at the same family of failures but in the opposite direction.
This guide covers P0012 across the 2020-2024 GMC Sierra 1500 generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 GMC Sierra 1500 with P0012?
In most cases a 2022 GMC Sierra 1500 stays drivable for short trips with P0012 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0012 on a 2022 GMC Sierra 1500?
- Check Engine Light is illuminated
- Loss of mid-range torque
- Sluggish acceleration
- Reduced fuel economy
- Rough idle
- Engine may feel "doughy" or unresponsive
- Possible cold-start cam-area rattle
What causes P0012 on a 2022 GMC Sierra 1500?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Stuck-closed VVT oil control valve (cannot direct oil to advance the cam) | Most common | $100–$450 |
| Low engine oil level or pressure | Most common | $50–$200 |
| Sludged oil galleries restricting flow to the phaser | Common | $100–$600 |
| Failed cam phaser stuck at base (retarded) position | Common | $600–$1,800 |
| Cam position sensor reporting offset position | Occasional | $100–$400 |
| Wiring fault between PCM and the OCV | Occasional | $80–$350 |
How to diagnose this on a 2022 GMC Sierra 1500
-
Check oil level and condition
Low oil starves the VVT phaser of working pressure. Confirm level is at full on a warm engine and oil is clean. Sludgy oil blocks the small passages that feed the phaser — change oil and filter with the correct viscosity before chasing further.
Tools: Dipstick check, Replacement oil and filter (if needed)
-
Measure oil pressure with a mechanical gauge
Confirm pressure is in spec at idle (typically 15–25 psi) and at 2500 RPM (40–60 psi). Low pressure must be repaired (oil pump, worn bearings) before the VVT system can function.
Tools: Mechanical oil pressure gauge
-
Test the intake OCV electrically and mechanically
Remove the OCV, inspect for sludge and metal at the inlet screen, and apply 12 V — the valve should click cleanly. Air should flow when energized and seal when de-energized. A stuck-closed valve cannot advance the cam, which sets P0012.
Tools: Socket set, 12 V test source, Brake cleaner, Compressed air
-
Command cam advance with a scan tool
A bidirectional scan tool can command the intake cam to advance while watching cam position in live data. A healthy system responds within 1–2 degrees of command. No movement points at the actuator (phaser); slow movement points at the OCV.
Tools: Bidirectional scan tool
-
Verify the cam phaser mechanically
If electrical and oil-side tests pass but the cam still does not advance, the phaser itself is stuck or worn internally. Replacement requires timing cover removal on most engines.
Tools: Engine-specific timing tools
NHTSA complaints & recalls for the 2022 GMC Sierra 1500
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 GMC Sierra 1500. Use these to gauge how common a problem is on your specific vehicle before you start chasing GMC Sierra 1500 diagnostics.
- ENGINE 207
- POWER TRAIN 92
- STRUCTURE 90
- ELECTRICAL SYSTEM 75
- UNKNOWN OR OTHER 70
6 active recalls
- EXTERIOR LIGHTING:BRAKE LIGHTS Jun 2022
General Motors (GM) has decided that certain 2022 model year Chevrolet Silverado, and GMC Sierra vehicles equipped with an accessory sport bar. The accessory sport bar contains a high-mounted brake light that may not function. In addition, it may block the vehicle's existing hi…
NHTSA campaign 22V463000 - EXTERIOR LIGHTING:LIGHTING CONTROL MODULE:SOFTWARE Dec 2022
General Motors, LLC (GM) is recalling certain 2020-2023 Cadillac CT4 and CT5; 2021-2023 Buick Envision; and 2022-2023 Cadillac Escalade and Escalade ESV, Chevrolet Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles. The daytime running lights (DRLs) m…
NHTSA campaign 22V903000 - POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE Oct 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control val…
NHTSA campaign 24V797000 - STRUCTURE:BODY:BUMPERS:ACTIVE SHUTTERS/GRILL Feb 2025
General Motors, LLC (GM) is recalling certain 2022 GMC Sierra 1500 vehicles equipped with chrome front grille deflectors. The attachments that hold the front grille deflectors in place may fracture, resulting in grille detachment.…
NHTSA campaign 25V060000
How do I fix P0012 on a 2022 GMC Sierra 1500?
- Change engine oil and filter with the correct OEM viscosity
- Clean or replace the intake-side VVT oil control valve
- Replace the intake cam phaser / VVT actuator
- Address oil pressure or sludge issue
- Replace the cam position sensor or repair wiring
About the 2020-2024 GMC Sierra 1500
The 2020-2024 GMC Sierra 1500 was commonly sold with the following powertrains: 5.3L V8, 6.2L V8, 2.7L Turbo I4, 3.0L Duramax I6 Diesel. Common trims include Pro, SLE, Elevation, SLT, AT4, Denali.
P0012 vs P0011
These two codes describe opposite-direction failures of the same hardware:
- P0011 — intake cam is over-advanced (stuck or commanded too far)
- P0012 — intake cam is over-retarded (cannot advance from base)
In practice P0012 is more common than P0011 because the default “stuck” position for a failing phaser is the base (retarded) position. The phaser advances under oil pressure; lose oil pressure and the spring retracts it.
What “over-retarded” actually means
The intake cam at base position represents the engine at idle. When the ECM commands advance, oil is directed into the phaser to rotate the cam relative to the crank. A stuck-closed OCV (or insufficient oil pressure) leaves the phaser at base — the engine runs but without the mid-range advance that gives modern engines their torque and economy. The result: sluggish performance and worse fuel economy.
When the OCV is the only repair needed
A surprisingly high percentage of P0012 cases on engines under 100k miles resolve with OCV cleaning alone — no replacement. The sludge that builds up at the OCV inlet screen restricts oil to the phaser. Brake cleaner and a soft brush, plus a fresh oil change, can clear the code for thousands of miles.